![connect garmin 545s to nmea 2000 network connect garmin 545s to nmea 2000 network](https://newcontent.westmarine.com/content/images/catalog/full/9040809_FUL.jpg)
- #CONNECT GARMIN 545S TO NMEA 2000 NETWORK INSTALL#
- #CONNECT GARMIN 545S TO NMEA 2000 NETWORK PROFESSIONAL#
- #CONNECT GARMIN 545S TO NMEA 2000 NETWORK SERIES#
Select a good viewing angle, and then tighten both knobs.ĭo not mount the transducer directly in the path of the Rotate the swivel mount bracket by twisting it left or right. Adjust the chartplotter angle, and tighten the long mounting knob until the chartplotter is snug.ģ. (Turn the knob counter-clockwise to widen the bracket arms and clockwise to tighten.)Ģ. If necessary, adjust the knob to spread the bracket arms apart. Align the slot on the back of the chartplotter with the long mounting knob, and slide the chartplotter into place.
![connect garmin 545s to nmea 2000 network connect garmin 545s to nmea 2000 network](https://data2.manualslib.com/product_thumbs/6/26/2533/253209_gpsmap_225_product.png)
#CONNECT GARMIN 545S TO NMEA 2000 NETWORK INSTALL#
To install the chartplotter on the mounting bracket:ġ. Place the swivel mount bracket over the swivel base and secure it with the short knob. Do not overtighten the screws or bolts you may damage the swivel base.Ĥ. Secure the swivel base with three bolts or screws.
![connect garmin 545s to nmea 2000 network connect garmin 545s to nmea 2000 network](https://atlaske-content.garmin.com/%2Fasset%2Fimages%2FNMEA2000male_female_Time1592511629230.png)
Do not make the starter holes deeper than half the screw length.ģ. (1.5 mm) starter holes at the locations you marked. If you secure the base with self-tapping screws, drill three 1/ 16 in.(5 mm) holes at the locations you marked. If you secure the base with machine bolts, drill three 5/ 32 in.Using the swivel base as a template, mark the location of the three holes that secure the bracket to the mounting surface. If you use screws with countersunk heads, you may damage the mounting bracket.ġ. Notice: Use pan-head machine bolts or self-tapping screws to secure the swivel base. (1.5 mm) drill bit for drilling starter holes. Or three #8 pan-head self-tapping screws and a 1/ 16 in. Three #8 (4 mm) pan-head machine bolts with matching nuts and washers and a 5/ 32 in. Use the included bracket to surface-mount the chartplotter.You will need the following tools and fasteners: For more information on the optional flush mount kit, visit or contact your local Garmin dealer. Flush Mount-use an optional flush mount kit to mount the chartplotter into a flat panel.The compact waterproof chartplotter housing is suitable for mounting in exposed locations or at the navigation station. Surface Mount-mount the chartplotter onto a bracket (included) that attaches to the console or overhead.
![connect garmin 545s to nmea 2000 network connect garmin 545s to nmea 2000 network](https://static.garmincdn.com/en/products/010-00671-00/g/cf-lg.jpg)
There are two mounting options for the chartplotter: This type of failure and related consequences are not covered by the manufacturer’s limited warranty. Extended exposure to temperatures exceeding this range (in storage or operating conditions) may cause failure of the LCD screen. The temperature range for the chartplotter is from 5☏ to 131☏ (from -15☌ to 55☌). Notice: Do not mount the chartplotter in an area that is exposed to extreme temperature or conditions.
#CONNECT GARMIN 545S TO NMEA 2000 NETWORK SERIES#
The chartplotters in the GPSMAP400/500 series have different functionality based on model number. Connect the cables to the chartplotter ( page 9).ħ. Connect the chartplotter to a NMEA 2000 network (optional, if applicable) ( page 8).Ħ. Install the transducer, if applicable ( page 3).ĥ. Notice: When drilling or cutting, always check the opposite side of the drilling or cutting surface.ģ. Warning: Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. WARNING: See the Important Safety and Product Information guide in the product box for product warnings and other important information. If any parts are missing, contact your Garmin dealer immediately.
#CONNECT GARMIN 545S TO NMEA 2000 NETWORK PROFESSIONAL#
If you experience difficulty installing the chartplotter, seek the assistance of a professional installer, or contact Garmin Product Support.īefore installing your GPSMAP400 or 500 series chartplotter, confirm that the package contains the items listed on the box. You need the appropriate fasteners, tools, and mounts listed in each section. Your GPSMAP 400/500 series chartplotter must be properly installed according to the following instructions. GPSMAP 400/500 Series Installation Instructions